jyetech scope - SMD parts
jyetech scope - probe assembly 1/7
jyetech scope - probe assembly 6/7
jyetech scope - empty backside
jyetech scope - SMD parts done
jyetech scope - probe assembly 5/7
jyetech scope - probe assembly 2/7
jyetech scope - "empty" board
jyetech scope - probe assembly 3/7
jyetech scope - probe assembly 4/7
jyetech scope - probe assembly 7/7
jyetech scope - only back side done
jyetech scope - 7805 regulator test
jyetech scope - 7805 regulator test
This crocodile even hase eyes!
jyetech scope - LCD
jyetech scope - all done: front side
jyetech scope - all finished: back side
jyetech scope - LCD assembled
jyetech scope
jyetech scope - fully assembled after milling
jyetech scope
jyetech scope
jyetech scope - all finished: back side
jyetech scope
jyetech scope - front panel too small
Bad RCA connector on a probe
jyetech scope - front panel too small
Jyetech scope - improved back plate
jyetech scope - fully assembled
Jyetech scope - improving the back plate
Jyetech scope - improved back plate
Ice Tube clock - PCBs 1/2
Ice Tube clock - PCBs 2/2
Ice Tube clock - parts 2/2
Ice Tube clock - voltage reg. 1
Ice Tube clock - voltage reg. 2
Ice Tube clock - voltage reg. 3
Ice Tube clock - buzzer 1
Ice Tube clock - buzzer 3
Ice Tube clock - boost conv. 1
Ice Tube clock - boost conv. 3
Ice Tube clock - buzzer 2
Ice Tube clock - boost conv. 2
iIce Tube clock - boost conv. 4
Ice Tube clock - VFD driver socket
Ice Tube clock - all except VFD driver chip
Ice Tube clock - VFD driver socket
Ice Tube clock - backup battery 1
Ice Tube clock - backup battery 5
Ice Tube clock - VFD driver socket
Ice Tube clock - backup battery 2
Ice Tube clock - backup battery 4
Ice Tube clock - VFD PCB
Ice Tube clock - VFD PCB
Ice Tube clock - VFD PCB attached
Ice Tube clock - mounted to base
Ice Tube clock - VFD PCB
Ice Tube clock - spacer nut
Ice Tube clock - boxing
Ice Tube clock - VFD alignment
Ice Tube clock - VFD soldered
Ice Tube clock - VFD attached
Perfect fit
Dimmed inner ring
PLCC2 variant - front
Code name: Lord Helmet
Code name: Lord Helmet
PLCC2 variant - back
V2.0 beta vs. alpha
V2.0 beta vs. alpha
Shot with -2.0EV
Beautiful colors
Some quality colors
It's still round
Lord Helmet
More light hack
More light hack
BCM vs. dumb software PWM
Almost looks like a little car
Perfboard
Salvaged LEDs
The End
The End
Burned LED
SMD to the rescue
Smoothing capacitor added
Smoothing capacitor added
Sad lamp - all on
Da Switch
All wired up
Attaching the PCB
Full frontal...
Look at me
Da Switch
Sad lamp - LED only
LED only
Eating perfboard
All on
Adding a switch for the light bulb
Eating perfboard
Test jig for DSOs
Test jig for DSOs
More details
Some signal
Full wave rectifier - strangeness
Full wave rectifier - strangeness
Full wave rectifier - with large cap
Full wave rectifier - with small load
Knock sensor waveforms
Full wave rectifier - strangeness
Knock sensor waveforms
Tektronix 314 - back cover removed
Logic vs. transistor driver
Logic vs. transistor driver
Logic vs. transistor driver
Logic vs. transistor driver
Ice Tube clock - boost conv. HF ripple
Ice Tube clock - boost conv. ripple
Ice Tube clock - boost conv. voltage
floating voltages
Tektronix 314 - floating power supply
Arduino speed measurement - 2µs/div
Tektronix 314: Arduino speed measurement - 0.1µs/d…
Jyetech - Arduino speed measurement
Keywords
Authorizations, license
-
Visible by: Everyone -
All rights reserved
-
91 visits
jyetech scope - other parts
Please note that a new hardware version of this device has been released, therefore these images will most likely not apply to it.
- Keyboard shortcuts:
Jump to top
RSS feed- Latest comments - Subscribe to the comment feeds of this photo
- ipernity © 2007-2024
- Help & Contact
|
Club news
|
About ipernity
|
History |
ipernity Club & Prices |
Guide of good conduct
Donate | Group guidelines | Privacy policy | Terms of use | Statutes | In memoria -
Facebook
Twitter
Sign-in to write a comment.