About to cut a trace
Waiting resistor
Mask removed
Tinned
Hopefully fixed - 8 more to go
Patch applied
Offender removed
Resistor's new home
ChipQuik to the rescue
Wrong choice of footprint
WHAT was I thinking?
Nichia NSPWR70CSS-K1
Dirty little suckers!
0402 LED - Phew...
Looks BGA-ish
Yes... it is TINY!
Where do I get an X-ray machine?
Solder paste - a bit too much
Adding the magic goop
Too much 'glue' ?
Application of 'glue'
Lighting up my kitchen workspace
Fixing the LED pin issue
Testing...
Impossible to capture the true purpleness
Old vs. New
Old vs. New
Old vs. New
I think I need a light tent
IMGP4433
Main amp
Input board
Input board
Input board
Nice attention to detail
Right speaker
Nice attention to detail
Right speaker - innards
Old lipo
Green PCB
DMM A/D
No external fuse access ;-(
Crappy substrate
Smoke detector - PCB
Smoke detector - PCB
Optical smoke sensor
Optical smoke sensor
RGB LED Ring - 2nd prototype
RGB LED Ring - 2nd prototype
RGB LED Ring - LED test
RGB LED Ring - LED test
RGB LED Ring - LED test
RGB LED Ring - LED test
New batch of boards
RGB LED Ring - V1.21 front side
RGB LED Ring - V1.21
Lord Helmet
PLCC2 variant - back
Code name: Lord Helmet
Code name: Lord Helmet
PLCC2 variant - front
Dimmed inner ring
Bodge wire
Planned ESD protection
Hotplate SMD reflow
He's dead Jim!
Trying to get good pin alignment
Pogo-pin adapter PCB
Pogo-pin adapter with assembly jig
Using the jig to assemble the pogo-pin adapter
AVR ISP pogo-pin programming adapter
AVR ISP pogo-pin programming adapter
There's a tiny spring inside!
These things are delicate
AVR ISP pogo-pin programming adapter
Pogo-pin programming adapter at work
AVR ISP pogo-pin programming adapter
AVR ISP pogo-pin programming adapter
Pogo-pin weak spot covered with blob of solder
AVR ISP pogo-pin programming adapter
AVR ISP pogo-pin programming adapter
Workplace
Iteadstudio 'Mystery PCB' service
Elecfreaks freebees - SO adapter
Elecfreaks freebees - adapter board
Fixed
Removing the gunk
Bodge job
The brain + LEDs
Lit LED
Bad solder mask
Quartz
Who made it
Bad solder mask
Rotting PCB
Rotting chip - RIP
Rotting chip - RIP
The brain of a toothbrush
TPC S8211 - 2 N MOSFETs
Rotting chip.
What naughty PCBs end up as
front side - darkish blue
A PCB coaster
A PCB coaster
Defective PCB - back side
Defective PCB - front side
This via sucks !
Purple everything!
LAEN's PCB - 1st order
Chained MBI5168 breakout boards
Finished MBI5168 breakout board
And the final batch works as well
RGB LED Ring - V1.21
Looks decent, but does it work?
Waiting for electrons
Project tinyfication
Pogo-pins
Panelmania
Panelmania
Left: better - Right: not so god
480 LEDs later...
LED port-status
LED port-status
Golden Dog
Lots of dogs
Keywords
Authorizations, license
-
Visible by: Everyone -
All rights reserved
-
190 visits
Cut trace
![Cut trace Cut trace](https://cdn.ipernity.com/133/69/47/23346947.53694e8b.640.jpg?r2)
![](https://s.ipernity.com/T/L/z.gif)
The result is pretty good. I think I could use an even smaller tool (spear-point drill). Using sub-1mm fluted end-mills can get a bit tricky, especially if they're not of the short and stubby kind. They break quite easily - and cost a lot.
- Keyboard shortcuts:
Jump to top
RSS feed- Latest comments - Subscribe to the comment feeds of this photo
- ipernity © 2007-2024
- Help & Contact
|
Club news
|
About ipernity
|
History |
ipernity Club & Prices |
Guide of good conduct
Donate | Group guidelines | Privacy policy | Terms of use | Statutes | In memoria -
Facebook
Twitter
Sign-in to write a comment.