High power RGB LED matrix prototype
Both side by side
imgp1996
Shine Baby Shine!
Step-up converter with LT1618
It's alive - and terribly small
LED's arse
Illuminated glass globe
It's alive - and terribly small
LED comparison
Illuminated glass globe - base
Will it shine, or will it pop ?
imgp1995
now I hate wires
1.8W G4 replacement
LEDs
High power RGB LED matrix prototype
Ah Xmas... the time to
Seeedstudio 3W LED bar
LED - uniformity issues
Ooops I did it again ;-(
My LAST perfboard prototype
LED - uniformity issues
perfboard moodlight
LEDs
LED - uniformity issues
1.8W G4 replacement
imgp2009
PT4115 full blast
LED-strip + custom controller
Improvised ISP connector
Finished MBI5168 breakout board
My LAST perfboard prototype
imgp2008
Chained MBI5168 breakout boards
Contacts
How to defend yourself against a man with...
LED strip - brightness vs. position
Obligatory arduino board
Me pointing at something
Another promo shot ;-)
PT4115 lowest setting
LED-strip + custom controller
PT4115 driver - modded
Another promo shot ;-)
TSOP-ed my kitchen lights
Me still pointing at something
ATtiny13 board doing PWM and sensing
Ah Xmas... the time to
Ah Xmas... the time to
The switch died, so I put in a LED
Ah Xmas... the time to
IR-upgraded LCD backlights
ATtiny13 LED-strip controller
IR-upgraded Ikea Samtid
imgp2007
UP/DOWN contacts
imgp2006
Ah Xmas... the time to
Ah Xmas... the time to
imgp2001
Ah Xmas... the time to
imgp2000
High power RGB LED matrix prototype
Lousy 'constant' current source
a long way to go
Illuminated glass globe - inside
DOH!
My LAST perfboard prototype
LED - uniformity issues
G4 replacement - 1.8W
Lousy 'constant' current source
almost done ?
Ooops I did it again ;-(
LED - uniformity issues
LED - uniformity issues
creative chaos
Illuminated glass globe - inside
LED - uniformity issues
LED - uniformity issues
LED - uniformity issues
High power RGB LED matrix prototype
And the final batch works as well
Looks decent, but does it work?
Waiting for electrons
Pogo-pins
Panelmania
Panelmania
Left: better - Right: not so god
480 LEDs later...
LED port-status
LED port-status
Slow but steady
Golden Dog
Lots of dogs
IR switch with PWM
It' alive
CUT!
Tindie logo for KiCad
Fixed fooprint + LED + shrunk
QUARTERS! I NEED QUARTERS!
ATtiny85 based IR switch
KiCad / gerbmerge panelization
IR PWM board
Translucence
Finally got these, too.
IR receiver - back side
IR receiver V1.10
IR raw receiver
IR receiver - front side
The final boards - green
Now with a voltage regulator
And the final batch works as well
The final boards - green
Inner ring fully on
IKEA Samtid - reading light mode
Final revision boards
IKEA Samtid - wall washer
Added another 8x 0805 LEDs
Added another 8x 0805 LEDs
V2.0.c front
V2.0.c backside
V2.0 beta
V2.0 beta
It started to snow today...
Keywords
Authorizations, license
-
Visible by: Everyone -
All rights reserved
-
88 visits
Step-up converter with LT1618
![Step-up converter with LT1618 Step-up converter with LT1618](https://cdn.ipernity.com/133/79/95/23337995.5926439d.640.jpg?r2)
![](https://s.ipernity.com/T/L/z.gif)
The current sensing resistor is still missing as I couldn't find 0.22Ω anywhere, but the chip also has adjustable output voltage support. I just measured the LED current and adjusted the voltage. That's not the right way, but this was an "emergency build" ;-)
Edit: The [expletive deleted] chip is dead !
Edit: The [expletive deleted] chip is dead !
- Keyboard shortcuts:
Jump to top
RSS feed- Latest comments - Subscribe to the comment feeds of this photo
- ipernity © 2007-2024
- Help & Contact
|
Club news
|
About ipernity
|
History |
ipernity Club & Prices |
Guide of good conduct
Donate | Group guidelines | Privacy policy | Terms of use | Statutes | In memoria -
Facebook
Twitter
Sign-in to write a comment.