Looks decent, but does it work?
And the final batch works as well
High power RGB LED matrix prototype
LED - uniformity issues
LED - uniformity issues
LED - uniformity issues
Illuminated glass globe - inside
creative chaos
LED - uniformity issues
LED - uniformity issues
Ooops I did it again ;-(
almost done ?
Lousy 'constant' current source
G4 replacement - 1.8W
LED - uniformity issues
My LAST perfboard prototype
DOH!
Illuminated glass globe - inside
a long way to go
Lousy 'constant' current source
High power RGB LED matrix prototype
Step-up converter with LT1618
High power RGB LED matrix prototype
Both side by side
imgp1996
Shine Baby Shine!
Step-up converter with LT1618
It's alive - and terribly small
LED's arse
Illuminated glass globe
It's alive - and terribly small
LED comparison
Illuminated glass globe - base
Will it shine, or will it pop ?
imgp1995
now I hate wires
1.8W G4 replacement
LEDs
High power RGB LED matrix prototype
Ah Xmas... the time to
Seeedstudio 3W LED bar
LED - uniformity issues
Ooops I did it again ;-(
My LAST perfboard prototype
LED - uniformity issues
perfboard moodlight
LEDs
LED - uniformity issues
1.8W G4 replacement
imgp2009
PT4115 full blast
LED-strip + custom controller
Improvised ISP connector
Finished MBI5168 breakout board
My LAST perfboard prototype
imgp2008
Chained MBI5168 breakout boards
Contacts
How to defend yourself against a man with...
LED strip - brightness vs. position
Obligatory arduino board
Me pointing at something
Another promo shot ;-)
Pogo-pins
Panelmania
Panelmania
Left: better - Right: not so god
480 LEDs later...
LED port-status
LED port-status
Slow but steady
Golden Dog
Lots of dogs
IR switch with PWM
It' alive
CUT!
Tindie logo for KiCad
Fixed fooprint + LED + shrunk
QUARTERS! I NEED QUARTERS!
ATtiny85 based IR switch
KiCad / gerbmerge panelization
IR PWM board
Translucence
Finally got these, too.
IR receiver - back side
IR receiver V1.10
IR raw receiver
IR receiver - front side
The final boards - green
Now with a voltage regulator
And the final batch works as well
The final boards - green
Inner ring fully on
IKEA Samtid - reading light mode
Final revision boards
IKEA Samtid - wall washer
Added another 8x 0805 LEDs
Added another 8x 0805 LEDs
V2.0.c front
V2.0.c backside
V2.0 beta
V2.0 beta
It started to snow today...
It started to snow today...
OLS pull-up/down wing
Finished MBI5168 breakout board
OLS pull-up/down wing
More light for my 'workbench'
Replacing a popped 7805
Upcycling old prototypes !
More light for my 'workbench'
Openbench logic sniffer - pull-down wing - Rev 0.1
MBI5168 breakout board
Openbench logic sniffer - pull-down wing - Rev 0.1
MBI5168 breakout board
OLS pull-up/down wing
OLS pull-up/down wing
OLS pull-up/down wing
MBI5168 breakout board
Old vs. New
Done - two more to go :-(
Old vs. New
Depth of Field
Depth of Field
Not faked at all
See also...
Keywords
Authorizations, license
-
Visible by: Everyone -
All rights reserved
-
194 visits
Waiting for electrons
![Waiting for electrons Waiting for electrons](https://cdn.ipernity.com/133/48/41/23334841.8965aff4.640.jpg?r2)
![](https://s.ipernity.com/T/L/z.gif)
Forgot to get the quartz, diode footprint doesn't quite match, still missing the programming adapter board... the usual stuff.
- Keyboard shortcuts:
Jump to top
RSS feed- Latest comments - Subscribe to the comment feeds of this photo
- ipernity © 2007-2024
- Help & Contact
|
Club news
|
About ipernity
|
History |
ipernity Club & Prices |
Guide of good conduct
Donate | Group guidelines | Privacy policy | Terms of use | Statutes | In memoria -
Facebook
Twitter
Sign-in to write a comment.